The View Up Here

Random scribblings about kites, photography, machining, and anything else

Posts Tagged ‘Audio’

Whales, Waves, and Unexpected Urination

Posted by Tom Benedict on 12/12/2016

“See any whales?”

I’d been recording at Kiholo Bay for several hours before the man spoke to me, but the first hour had been plagued by technical issues. For some reason my DR-70D kept reporting a write timeout error – something usually attributed to using a slow memory card – but I knew the card was good. Helicopters and airplanes had ruined the rest of the first hour.

At that point I was almost done with my first completely clean hour of waves on my SASS and Mid-Side setup. My other recorder, a DR-05, was positioned at a small beach to the south of me, recording waves receding off of loose pebbles.

I turned around to see who’d spoken to me. He was an older man who’d been hiking along the coast and had stopped to talk. I knew his words would show up on the recording, so I figured if I’m editing I’m editing. I might as well be civil about it.

“No, not from here.”

He nodded and walked on. I turned back to my gear, but out of the corner of my eye I saw him turn and head down to the little pebble beach.

People here are, on the whole, really nice about other people’s stuff. At one point years ago I left some kites at Hapuna Beach, one of the busiest beaches on the Big Island. It wasn’t until I was unloading my car at home that I realized my kite bag was missing. I jumped back into my car, headed back to the beach, and found that someone had brought my kites up off of the sand and left them for me at the showers. People here really are great.

But still… Strange guy hiking down to a beach where I’d left gear… I didn’t want him knocking my gear over inadvertently or anything. So I kept an eye on him as he made his way down to the beach and… proceeded to relieve himself not four feet from where I’d left my gear. Recording sound. All sound. Beach sound. And now his sound. His very personal sound. He kept glancing up at me like I was being rude. I did turn away while he was occupied with his… task. But eventually I knew he’d finish and realize I’d been recording him. Which he eventually did.

One of my more awkward sessions.

(But I got a lot of really good winter wave on rock sounds!)

Anyway, I think I’ve finally answered some open-ended questions about microphones. The Alice microphones I’ve been building are beautiful, crisp, and punchy, but not all that great for recording outdoor sounds. They’re very bright, which works great for a number of subjects. Waves, streams, and wind in the trees just don’t happen to be any of those subjects. Unfortunately those are the subjects I’m interested in.

I also don’t think I’m a huge fan of mid-side recording for creating big spacious soundscapes. No matter how much I play with the balance of mid to side, I just can’t get as much of a sense of space as I do with the SASS. I find myself firmly in the camp of the partially baffled microphone array. So for now I’ll save the mid-side and LDC Alice mics for indoor recording and go back to my Primo-based mics for nature. (Though I still intend to convert my Behringer C-2 mics to surface-mount Alice electronics. They’ll make good instrument mics, if nothing else.)

There’s one last test I want to repeat, though. Early on I built an Olson Wing – a baffled double-boundary array invented by Curt Olson. This pre-dated my SASS. I remember I liked the sound, but that I liked the sound of my SASS better. Now that I’ve had a chance to try a number of other stereo recording techniques (X-Y, A-B, ORTF, M-S, and SASS), I’d like to resurrect my Olson Wing and try it and the SASS side-by-side. I’ve still got all the bits, so it’s just a matter of rigging everything back up and getting out with the gear.

It’s something of a pressing question because of something else that happened. Earlier today my wife bought me an early present: a pair of ammo boxes.

I joked with the kids that they’re for the Zombie Apocalypse. They just rolled their eyes. They know me too well. She got me the ammo boxes for a recording project.

One of the problems with unattended recording is that conditions change, weather turns, and gear gets rained on. My first unattended overnight session wound up that way. I set up to record the dawn chorus in the Upper Waiakea Forest Reserve on International Dawn Chorus Day, but during the night the clouds came in and rained on my gear. The evening chorus was spectacular, but with the rain on the leaf mast making a staccato drumming sound, the dawn chorus part of the recording was practically useless.

My gear survived, but the weather proofing was tentative at best. I’ve been looking for a good way to build a completely watertight, rain proof recording setup. Enter the ammo box.

Ammo boxes are made out of steel. They’re tough. And they have a rubber weather seal that’ll keep out a hurricane. Perfect for cramming recording gear into! My plan is to use the larger of the two boxes to house my gear, and either build an Olson Wing or an SASS around the box, depending on which one I like better. The microphones would be the only thing poking out. Everything else goes inside the box, which can then be latched shut. The whole unit can then be left overnight without any chance of rain getting inside and killing my gear.

Or pee, for that matter.

Posted in Audio, Engineering | Tagged: , , , , , , , , , , , , , , | Leave a Comment »

Building the MS Alice Microphone – Part 2

Posted by Tom Benedict on 23/11/2016

This is the second half of a two-part article describing my build of the mid-side Alice microphone, following the Instructable written by Jules Ryckenbusch: Build the MS Alice Stereo Microphone. In Part 1 of this article I ran through how I was planning to build it (mostly following the same steps I used in another two-part series I wrote about another of Jules’s Instructables, Modify a Cheap LDC Condenser Microphone, namely: BM-800 Microphone Conversion Part 1 and Part 2.) I also covered my design for the saddle and post that holds the three capsules in the particular orientations required for Jules’s MS microphone build. (Jules used a different method, using PVC pipe, which you’ll see in his Instructable if you decide to build one of your own.)

Since writing Part 1 all the bits and pieces came in. I was eager to see how the 3D printed saddle and post turned out, and how well the TSB-165A capsules fit.

M-S Alice Capsule Saddle and Post - Unpopulated

I designed the cavities for the capsules at-size, meaning I didn’t leave any slop for fit. The plastic Shapeways uses to make their least expensive printed parts is described as “strong and flexible”. I took them up on that, figuring the part would flex enough to allow the capsules to snap into place. It worked like a charm.

M-S Alice Capsule Saddle and Post - Populated

The fit is snug, but not snug enough to hold the capsules in use. As with my first Alice, I glued the capsules into the saddle with E-6000 adhesive.

I’m a little disappointed with the handling noise on my first Alice mic. I chalk some of that up to the metal saddle and post, but some of it I chalk up to the relatively stiff wire I used to connect the capsule to the PCB. It was stiff enough that manipulating the wire wound up breaking off one of the ground tabs from the TSB-2555B capsule I used on that mic. Rather than repeat that experience, and in an effort to reduce conduction paths for handling noise, I gutted some of the Mogami cable I use for all my microphone projects and used the wires to connect the capsules. (NOTE: It didn’t actually affect handling noise that much. After thumping various bits of the mic, I’ve come to the conclusion the dominant frequency of the handling noise is driven by the resonant frequency of the mesh in the headbasket.)

I already had two Pimped Alice PCBs built, tuned, and ready to go for this project. The remaining steps were to screw one board onto each side of the mic frame, solder the capsule wires to the boards, solder the four 0.022uF capacitors between the ground pin (pin 1) and the remaining pins of the XLR connector (2, 3, 4, and 5), and to solder wires between the XLR and the PCBs.

M-S Alice Internals

Since I oriented the two capsules of the figure-eight mic side-by-side, they won’t fit inside the headbasket with the foam liner in place. So I stripped the foam out before closing up the mic.

The very last step was to build the 5-pin XLR to dual 3-pin XLR splitter cable. There are a number of ways I could’ve done this, but I followed (mostly) Jules’s build on the cable as well, using separate Mogami lavalier cables for each channel. This is a wonderfully floppy wire, and does an excellent job of reducing handling noise transmitted through the cable.

The one change I made to Jules’s design was to jacket the central eight feet of cable in a woven sleeve to keep it from tangling.

M-S Alice Patch Cord

I left the last foot and a half at each end loose, though, to take advantage of the wire’s floppiness. (Hey, that’s actually a word spellcheck recognizes!)

And at long long last I’m able to play with mid-side recording and compare it against my EM-172 based SASS.

SASS vs. M-S Comparison

Big big thanks to the following for making this all possible:

  • Jules Ryckenbusch – for writing the two Instructables that got me going on these microphones
  • Homero Leal – for coming up with the PCB layout for the Alice boards used in Jules’s Instructables
  • Scott Helmke – for designing the Alice circuit in the first place
  • Ricardo Lee and all of the above – for their endless patience with all of my questions and what-ifs
  • Dr. Ing – for designing the Schoeps CMC-5 in the first place, without which none of this would exist

For my own contribution, here’s the link to the MS Alice capsule saddle and post on Shapeways. I’ve listed these at-cost, with no mark up (meaning I don’t see a dime of the 5.35 USD price tag at the time of this writing – labor of love).

Have fun recording!


Posted in Audio, Engineering | Tagged: , , , , , , , , | Leave a Comment »

Building the MS Alice Microphone – Part 1

Posted by Tom Benedict on 11/11/2016

This is a short pair of articles that glosses over most of the details of how I’m building a self-contained mid-side (MS) Alice microphone into a Neewer NW-800 microphone body. Part 1 covers most of the design and preparation, and Part 2 will cover the build.

The reason why this pair of articles is so brief is that most of the nitty-gritty was already covered in another pair of articles: BM-800 Microphone Conversion Part 1 and Part 2. The major differences between that microphone and this one are a change in capsules (Transsound TSB-165A instead of a Transsound TSB-2555B), the number of capsules (three instead of one), the number of Pimped Alice boards (two instead of one), and a change tof XLR connector (5-pin rather than 3-pin).

With the exception of how I’m planning to mount the capsules, all of this follows the Instructable written by Jules Ryckenbusch: Build the MS Alice Stereo Microphone. That’s the real reference for this build, so if you decide to build one of these yourself be sure to follow Jules’s notes.

The easy stuff first:

When I built my first Alice microphone I built three PCBs rather than just the one I needed, so I already have two Pimped Alice boards ready and waiting in the wings. I was on the fence whether to build a second mic around a TSB-2555B capsule or go straight to the MS Alice. After some recent field tests, I decided to commit the two boards to an MS Alice.

Jules pulled a neat trick for getting two signals out of a single XLR connector: use a different XLR connector! In his build he replaced the 3-pin XLR that came with his BM-800 microphone with a 5-pin. The two outputs share a common ground, but have independent signal pins. I’m following this part of his plan to the letter. (As a side note, this also gives me a spare 3-pin XLR connector to use when I finally build out my parabolic mic. New project in the works!)

The only things left to do were to order three TSB-165A capsules (done) and to figure out how to mount them.

Jules has a nice tutorial on how to build a 3-capsule saddle out of PVC pipe, but I had so much fun machining a custom saddle for my TSB-2555B capsule, I couldn’t pass up the opportunity to massively over-complicate life by designing a custom saddle for the MS Alice as well. Here’s what I came up with:

MS Alice TSB-165A Capsule Saddle

Which looks neat and all, but would be stupidly difficult to machine. It’s possible, provided you got rid of, or at least filleted the inside corner between the two side capsules, but it wouldn’t be fun. And since this is all about fun, I cheated. I sent it off to be 3D printed out of nylon. (If this pans out and there’s any interest, I’m happy to make the 3D model available for other people to print.)

So now I’m back to playing the waiting game. I’ve got parts coming in from Redco Audio (5-pin XLR to dual 3-pin XLR splitter cable), Mouser (smaller capacitors for the Alice boards to address the space constraint issue I ran into), Amazon (Switchcraft 5-pin XLR connector, NW-800 body, and associated doodads), JLI Electronics (three TSB-165A capsules), and finally Shapeways (the 3D printed mic saddle).

I’ll write the second half of this series once all the goodies show up.


Posted in Audio | Tagged: , , , , , , , , | 1 Comment »

Alice and Behringer Sitting In A Tree – Part 1

Posted by Tom Benedict on 03/11/2016

The field tests on my BM-800 Alice conversion will have to wait. Late last week I handed it over to a friend for tests I’m not equipped to make, including several mic comparisons. I’m eager to see (and hear!) his results.

Meanwhile my Behringer C-2 mics showed up. These are the ones I placed a bid on over at Ebay before I realized they were coming from Haifa, Israel. Despite the distance the shipping was actually less than FedEx charges to ship a letter-shaped package from the mainland US to Hawaii. (Go figure.) It still ramped the price of the mics up almost to market value, which on Amazon with its super saver free shipping basically means I could’ve ordered them new and had them weeks ago.

But they’re here. And they’re mine. And… to be honest they’re in pretty ratty shape. One of them had something loose in the capsule. If you pointed the mic up and shook it, it made a hellish noise and clipped constantly. Turn it upside down and shake, and you hear something rattling around. The other mic has something massively wrong with its circuit board. It sounds for all the world like a Huey is hovering overhead. Bup bup bup bup bup bup bup… It never ends.

So long story short, I don’t mind gutting these things and building something new. In the short term I put the good capsule on the good mic body so I have one working mic to play with. The other one I started taking apart.

Behringer C-2 Capsule Removed

These have interchangeable capsules, though I don’t know if Behringer (or anyone else) makes any other capsules for it. The one that came with my mics is a hypercardioid. (At least that’s what the icon on the side of the capsule looks like.) Given the size of the vents at the back, I can believe it.

Underneath the capsule is a white plastic plug with a pogo pin centered in it. Not much to look at. And no real clue how to open things up past there.

To gain access to the innards of the mic, peel back the the “Behringer Condenser Microphone” name tape at the base. This reveals a small set screw that should be familiar to anyone with Switchcraft XLR connectors. Screw the set screw all the way in. This releases the XLR connector from the body. Next, center the pad/high-pass filter switch and pull the switch button out with needle nose pliers. Finally, push on the white plastic plug to expose the circuit board.

Behringer C-2 Stereo Pair - Partially Disassembled

Here’s what’s inside:

Behringer C-2 PCB Top

Since one of my mics has a damaged board, rather than figure out how to tweak what’s already here, I went ahead and tried to figure out how to pack a Pimped Alice into the same board space. I started by taking measurements.

The board is 15.5mm wide x 52.35 mm long, and is 1mm thick. The thickness is important because the board slots into the white plastic insert. One nice thing about this method of mounting the board is that there are no screw holes, and except for the humongous XLR pins and the 2mm area that slots into the plastic insert the rest of the real estate on the board is free. The board is mounted just below the centerline of the mic, so there’s vertical room as well. Up to a point, anyway. Those capacitors are 6.5mm diameter x 8mm tall. Nothing bigger than that will fit, even centered on the board.

There’s really not enough room to use through-hole components everywhere, so I converted most of the Pimped Alice circuit to 0805 SMT components. The exceptions are the filter capacitors, the 1Gohm resistor, and the FET.

There seems to be some resistance to using surface mount technology for DIY mics, but SMT has been used for over a decade for DIY robotics and electronics. I’ve built AVR processor boards using SMT components, and figured this wouldn’t be much different. With the exception of the big filter caps and the FET, that’s how Behringer built the original board for the C-2, so I figured it was a safe way to go. As soon as I have a new PCB layout, I’ll send it out for fab.

Meanwhile I started taking apart the capsule. Just looking through the grille, it seems like the C-2 uses a Transsound capsule similar to the TSB-165A Scott Helmke used in the original Alice.

Behringer C-2 Capsule Front

I started by removing the back plate. This is just pressed into place, but it’s a bear to get out. I eventually removed it by gripping it by an inside edge with needle nose pliers (pushing outward), and spinning it out. It took a couple of attempts, but it came apart.

The rear side of the capsule has an open cell foam washer in it, presumably to provide wind protection and to act as a delay plate to shape the hypercardioid pickup pattern. With the washer removed, the back side of the capsule is visible, held in place by a brass retaining ring

Behringer C-2 Capsule Back - Baffle Removed

The holes in the ring are really tiny. My existing pin wrench didn’t work, so I used an old divider with dull points as a pin wrench. There’s a bit of red enamel to prevent the ring from backing out, which took a little force to crack. Once that was done, though, the ring backed out easily. (I’ll need to be sure to apply a fresh bit of enamel when I get the new capsule installed.)

Behringer C-2 Capsule Disassembled Back

Behringer C-2 Capsule Disassembled Front

I was hoping the capsule was a Transsound TSB-165A, the same one Scott Helmke used in his original Alice microphone. Unfortunately it’s not. The capsule in the C-2 is 16mm in diameter x 6mm thick. The TSB-165A is 16.5mm x 8mm. But after some poking around on the JLI Electronics web site I think I found a match: the TSB-160A. The specs are almost identical to the TSB-165A, so it should play nicely with the Alice circuit (yay!), but the form factor matches what’s in the C-2. I’ll order a pair of these when I place the order for the 165A capsules for my MS Alice.

Behringer C-2 Capsule Mesh Outside

Another concern with the C-2 capsule holder is how the capsule is recessed, and how close the edges of the holder come to the input ports on the capsule. From my experiences with my first rev of mic bodies, I know that can color the sound enough to hear it. I’d like to open this up, if possible. It’s a simple enough job on a lathe as long as I can get the grill out.

Behringer C-2 Capsule Mesh Inside

The grill looks like it’s a two-layer mesh that’s either glued or soldered into the capsule holder. That should be easy enough to remove with heat, one way or the other. I might even be able to re-use it if I’m not too rough getting it out.

The grill serves two purposes. First and foremost, it’s an RF shield to keep stray electromagnetic radiation from getting into the signal path. Second, it helps to keep the capsule free of debris. Third, some manufacturers will stick enough mesh in front of the capsule to act as a rudimentary pop filter, and at least reduce the effect of wind. The problem with that third purpose is that you need a lot of tight mesh to pull that off. Enough so that it colors the sound of the mic. Not surprisingly, one of the more obvious mic mods is to remove a layer of mesh from the capsule housing.

But given how open the outer mesh is, I’m afraid it will make the mic prone to RF interference. For now I’ll leave it alone.

The next steps are to finalize the design of the new board, send it out for fab, and source all the components and capsules. But before I can finalize the board design I want to see if I can add in one of the features of the C-2: The switch on the side of the mic lets you select a high pass filter or a -10dB pad. If I can find the real estate on the board to accommodate the switch and the components necessary to add these into the Alice circuit, I will.


Posted in Audio, Electronics, Engineering | Tagged: , , , , , , , , , , , , , , | Leave a Comment »

BM-800 Microphone Conversion Part 2

Posted by Tom Benedict on 22/10/2016

This is the second half of a two-part article describing my conversion of a BM-800 microphone to an Alice microphone using a Transsound TSB-2555B cardioid capsule. All of this is based off of a pair of Instructables written by Jules Ryckebusch: Modify a cheap LDC Condenser microphone and Build the MS Alice Stereo Microphone.

Part 1 of this article showed pretty pictures of the donor mic (a Neewer NW-800 with an excess of bling), a description of the cable that came with the mic (which I don’t intend to use), photos of the mic in various stages of disassembly, and a CAD drawing of the salient features inside the microphone to help others lay out circuit boards for their own conversions.

Since writing part 1, all of the bits and pieces I ordered to do the conversion arrived: enough electronics to build three Alice boards, and a TSB-2555B capsule to put in the first one.

Everything for an Alice Conversion

Before populating the boards I did a test fit to make sure they would actually fit. I was pleased to see how well the screw holes lined up, and I came pretty close with the taper.

NW-800 With Alice PCB

The next step was to populate the boards. Opinions differ on how to wire the high-impedance (high-Z) end of the board, so I started with all of the low-Z components.

The circuit used in Jules’s first article had zener diodes on the output stage to protect it against over-voltage on the XLR pins. The circuit as-built in his second article omits the zeners since the 2N5087 transistors are rated for more than the 48V likely to be seen on an XLR connector. I ordered the zeners, but left them out for now.

Alice Trio with Low-Z Components

After I’d already wired all the boards I installed one in the mic and ran into my first problem: With the board installed right-side-up, the 47uF capacitor pokes up high enough that it interferes with the body tube. For my first mic I’m planning to install the board up-side-down to give the capacitor more room. But if I wind up building the MS mic from Jules’s second Instructable, I’ll need to install new capacitors that lay flat against the circuit board.

BM-800 Alice Board Placement

The reason for the difference of opinions on the high-Z end of the circuit is that it’s sensitive to contamination: leftover solder flux, dirt, dirt combined with humidity, oxidization, etc. on the high-Z end can all cause unwanted noise in the mic. Jules soldered his components to the board without issue. Others have used Teflon standoffs to float that part of the circuit above the PCB. Homero Leal built his Charis mic by point-to-point soldering the high-Z components, letting them float above the board without standoffs. Scott Helmke, the original designer of the Alice circuit, solders the high-Z components directly to the back of the mic capsule. For my first pass at this I soldered the low-Z legs of the FET to the board, but floated the high-Z circuit without stand-offs, similar to Homero’s Charis mic. I can always change my mind later and re-wire them.

High-Z Components Air-Floated

With the board built, the next step was to add 22nF capacitors between pins 1 and 3 and pins 1 and 2 on the XLR connector to provide additional RF noise filtering. After that I installed the modified connector and the board in the mic body.

Alice Board and XLR with RF Filter Caps

The rest of the action takes place inside the headbasket.

It’s possible to cut away the original mic capsule to leave a saddle for mounting the TSB-2555B, but I wanted to make an entirely new saddle. Chalk some of this up to not wanting to make a modification I can’t back out. Chalk some of it up to my wanting a machining project to go along with the electronics project. Either way it needlessly complicates an otherwise pretty simple project.

Space inside the headbasket is tight, so rather than run into more interference issues I fleshed out the 2D CAD drawing and turned it into a 3D model. The space constraints almost entirely dictated the shape of the new saddle and post. The mic frame is drilled and tapped for M2.5 screws on a 10mmx15mm rectangular pattern, only two of which are used on the original saddle. I chose to use all four. The mic wires pass through holes spaced 20mm apart, centered on the long axis of the bolt pattern. In the CAD model I indicated these with 3.13mm holes, but in the final part I cut them as slots to make installing and removing the capsule easier.

Mic Saddle - CAD vs. As-Built

I attached the TSB-2555B capsule to the saddle with E-6000 silicone adhesive. A better method for the saddle shape I used would’ve been a polyurethane adhesive like Gorilla Glue, but I wanted to be able to remove the capsule in case I decide to add shock isolation inside the mic to cut down on handling noise. As-built the capsule can be removed by passing a fine wire between the capsule and the saddle, cutting the silicone bond.

EDIT: The first time through, I missed an important step: One of the charms of the Pimped Alice circuit is the potentiometer next to the 1Gohm resistor. It allows you to bias the FET properly, regardless of which FET you use. The catch is that by definition, if you don’t do anything with the potentiometer it will not be properly biased! In all ignorance I soldered everything up, closed up the mic, and went testing. Even with an improperly biased FET it still performed beautifully. I did go back and do a proper job of it, though.

In Jules’s first Instructable, toward the end, there’s a nice write-up for how to bias the FET. The catch is that this step must be done before the capsule is soldered to the board.

With the FET properly biased and the capsule attached to the saddle and post, all that was left was to put it all together and close it up.

Finished BM-800 / TSB-2555B Alice

I did a quick side-by-side against one of my Primo-EM184 cardioid mics. The Alice runs a little hotter, but not by too much. I’m reserving further judgement on the new mic until I have a chance to get it out in the field and try it on some quiet sources.


Posted in Audio, Electronics, Engineering | Tagged: , , , , , , , , , | 3 Comments »

BM-800 Microphone Conversion Part 1

Posted by Tom Benedict on 09/10/2016

Several posts ago I mentioned a plan to build an MS mic by following an Instructable written by Jules Ryckebusch. Jules used a BM-800 microphone as a donor mic and replaced its guts with two Pimped Alice circuits and three cardioid capsules. After several Ebay vendors whose listings indicated they would ship to Hawaii later changed their story and said they wouldn’t, I finally picked up a BM-800 microphone off of Amazon. The one I got is a Neewer NW-800. (I liked its shock mount better than the other one I found.) It arrived, and I started poking and prodding at it.

Along the way I discovered another reason to use a windscreen on a microphone. This thing is bling central. To be fair some of the other BM-800 mics I found on Ebay didn’t have nearly as much… presence… but this is the one I could get.

Neewer NW-800 Bling

Unless I’m recording birds that are drawn to shiny objects the windscreen will probably become a permanent fixture on this mic, just to keep me from going blind.

Neewer NW-800 Windscreen

Before tearing into the thing I decided to try it as-is. On the face of it it’s a phantom powered cardioid condenser mic. This means plugging it into a device that doesn’t provide some kind of power (aka my laptop, my phone, even my kids’ desktop computer) won’t work.

The mic has a male XLR jack at the back, and came with an XLR-to-3.5mm cable. 3.5mm inputs that provide power typically provide plug-in-power (2.3V to 5V, depending on the device). XLR inputs provide phantom power (typically 12V, 24V, or 48V). That discrepancy made me a little leery of just plugging this into whatever and cranking volts through it. I started by ringing out the cable to see what it was actually doing.

XLR to 3.5mm Cable

Up to this point all the XLR plugs I’ve dealt with have been for balanced signals. That is to say that one pin of the 3-pin XLR is ground (pin 1), another is the positive signal (pin 2), and the third is the inverse or negative signal (pin 3).

3.5mm inputs typically use a TRS connector and unbalanced signals. In the case of the 3.5mm stereo input on my recorders the tip is the left positive channel, the ring is the right positive channel, and the sleeve is ground.

The cable supplied with the BM-800 ties XLR pins 1 and 3 together and routes them to the sleeve of the 3.5mm plug, and routes XLR pin 2 to both the tip and ring of the 3.5mm plug. This effectively turns the balanced output of the mic into two channel mono unbalanced output on the 3.5mm plug, meaning it should be able to be plugged into any 3.5mm stereo input and drive both left and right channels with the same signal. Neat!

What this also means is that as long as the mic can run on a wide range of voltages, the plug-in-power on any recorder should be able to drive this thing. So should the battery box I got from Church Audio. Or by removing the XLR-to-3.5mm cable and plugging in an XLR-to-XLR cable, I should be able to power it with phantom power (12V or 48v – the only two options on my recorder) and use it as a single channel balanced input.

Still leery of running such a wide range of voltages through it, I tried all three configurations anyway. I’m planning to gut this mic, after all, so if I burned it out the loss would be minimal. To my surprise all three worked! The plug-in-power on my DR-70D puts out a little under 3V, and my battery box from Church Audio puts out a little over 9V with a fresh battery. The 48V phantom power on the XLR inputs on the DR-70D put out right around 48V. I noticed a gain difference between the PiP and battery box, but because of the different gains on the XLR vs. 3.5mm inputs on the DR-70D I wasn’t able to tell if the additional voltage was doing anything to the mic itself. (My guess is it doesn’t. To survive that wide a range of voltages I’m guessing the mic has a voltage regulator on board. Past a certain point it’s just dissipating as heat.)

So how does it sound?


How to put this…

I’ve seen the shock mount it came with listed for more than what I paid for the mic. I don’t think this is too far out of line with how it sounds. It’s not bad, mind you. It’s just not anything I’d write home about. A little creative EQing would probably make it a decent podcast microphone. But as for making ambient nature recordings? Mmmm… no.

So without further ado I tore into it to see what I was going to have to deal with.

Neewer NW-800 Disassembly: Assembled

The first step in disassembling the microphone is to unscrew the butt cap. This also releases the shell, which simply slips off to expose the circuit board. The shell is keyed to a tab just under the headbasket which fixes the orientation of the logo on the mic. This is important since the mic is a side-entry rather than end-entry, meaning sound must enter from the side and not the end. Added to that, it’s a directional microphone so it’s only sensitive on one side. Can you guess which side? (Answer: The one with the logo.)

Neewer NW-800 Disassembly: Shell Removed

Some nice features on the inside of the thing: First, there’s a ton of room. Second, there’s a nice frame with mounting holes tapped for M2.5 screws. (More about those in a sec.) The only weird part is the taper on the frame and the circuit board. I like the look of the tapered board, so I decided to taper the boards for my Alice conversion, too, and put mounting holes in the boards to make use of the holes in the NW-800 frame.

Neewer NW-800 Disassembly: Headbasket Removed

Two M2.5 flat head Phillips screws hold the headbasket in place. They’re located just under the headbasket, above the circuit board. Once the screws are removed the headbasket lifts off, exposing the capsule.

Despite the appearance, the capsule in this mic is the same size as the EM-172 and the EM-184 capsules from Primo: 10mm diameter. At this point I was sorely tempted to gut the mic, drop an EM-184 capsule in the mic saddle, and call it quits. But the whole purpose of this exercise is to move beyond Primo all-in-one capsules and try my hand at building more complicated (and better performing!) microphones.

Neewer NW-800 Disassembly: Circuit Board Closeup

All of this starts with the circuit board.

Simple stuff first: The screws are M2.5, spaced 30mm apart. They’re biased a couple of millimeters above the centerline of the cavity. If you’re planning to make a rectangular circuit board to fit inside this mic, that’s probably all you’ll need. (The tube with the logo has vertical walls, so a rectangular board will fit fine.)

Since I wanted to make a tapered board I measured the whole cavity and threw it into CAD. At some point I’ll draw it in 3D, but for now a 2D representation is plenty for me to design the new board outlines. I’m building the Alice boards using through-hole components, so I needed a little more real estate than the original board provided. The 2D drawing of the cavity and the new board outline looks like this:

2D CAD - NW-800 Cavity and Board Outline

I sent the boards out for fab and ordered enough components from Mouser to build out three of them. One is destined to receive the TSB-2555B capsule I ordered from JLI. The other two will eventually be used to build a copy of Jules’s MS mic using three TSB-165A capsules, but that’s a project for another time. Once all the bits arrive I’ll write the second half of this article, which will cover the construction of the TSB-2555B mic.


Posted in Audio, Electronics, Engineering | Tagged: , , , , , , , , | 3 Comments »

Building New Mics

Posted by Tom Benedict on 17/09/2016

When you’re faced with a dilemma like choosing the next step to improve your recording gear, instead of finding the right answer to the question, sometimes it’s more fun to dodge the issue completely and go off on a tangent.

So I went off on a tangent! Building new microphones!

I’ve currently got two projects in the works. A parabolic mic and a self-contained mid-side mic.

The Parabolic

I’m basing my parabolic mic off of the family of parabolic mics  from  Telinga Microphones. The mics from Telinga offer all kinds of neat options. One contains a cardioid mic facing the parabola and an omni facing away from the parabola. This lets you record a distant sound and the ambient sound field at the same time on two different channels. Another contains two omnis on either side of a baffle plate so you can record a distant sound in stereo.

But at its simplest, a parabolic microphone uses a parabolic reflector to direct pressure waves at a single microphone located at or near its focus. That’s where I’m starting.

I picked up a 22″ parabolic dish from sdill471 on Ebay. He sells them for around 50USD and ships all over the place, including Hawaii (yay!), using USPS shipping.

The microphone for this project is the first EM-172 lavalier mic I built back when I started building external mics for my DR-05. It’s since been converted to XLR and received the full shielded treatment the rest of my EM-172 mics got when I did that conversion.

The rest of the project will be to make all the mechanical bits to place the EM-172 mic at the focus of the dish. I’m drawing a good bit of inspiration from WW Knapp’s Homemade Parabolic Mic page, though I’m making two big departures Knapp’s design: The first is to think more in terms of parts I can make in a machine shop rather than what I can find at the hardware store. (This departure is called “needlessly complicating a good, simple design”.) The other is to take a tip from Klas Strandberg at Telinga: You don’t always want the mic to be at the exact focus of the paraboloid. Having the ability to rack the microphone through focus gives you some much needed flexibility in the field to widen or narrow the pickup pattern of the mic, or even to tune which frequencies are focused on the mic by the dish.

I’ll post the design and build articles once I’ve finished the mic.

Mid-Side Microphone

The entire idea for the self-contained mid-side microphone comes from an Instructables article written by Jules Ryckebusch. Jules took a BM-800 mic – about ~20USD off of Ebay depending on the seller – gutted it, and replaced its innards with two Pimped Alice amplifier boards and three TSB-165 capsules. The really clever part is how he did it, but for any of that to make sense it helps to understand how mid-side microphones work.

The easiest way to understand mid-side recording is to read a really good article about it. What I wrote below won’t be nearly as good, so I urge you to follow that link. That being said, here’s my take on mid-side:

Back when recording was in its infancy no one even thought in terms of stereo recordings, quadrophonic, 5.1, 7.1, or any of the other immersive formats we’ve since come up with. Mid-side was one of the earliest stereo techniques, patented by Alan Blumlein in 1933.

Mid-side uses two microphones: one to pick up the center part of the sound field (the “mid” mic) and another to pick up the sound on either side (the “side” mic). In most cases the mid microphone is a cardioid, which preferentially picks up sound in front of the mic. In all cases the “side” mic is a figure-eight – a microphone that picks up sound in two opposite directions, but nowhere else.

To create what we consider a conventional Left-Right stereo image from a Mid-Side (M/S) recording requires a little math. The equations look like this:

Left = Mid + (+Side)

Right = Mid + (-Side)

In the equations the Mid channel is taken as-is. The Side channel is used twice: first it’s used as-is (+Side) and the second time it’s used inverted (-Side).

As wonky as that sounds, and as convoluted as the post-processing sounds, it offers some distinct advantages when mixing the tracks afterward. Want a wider stereo sound? Mix in a little more of the Side channel and a little less Mid. Want to focus the listener’s attention on the bird in front of the mic and down-play the forest full of frogs chirping in the background? Bump up the Mid and turn down the Side. Want to mix a mono track to go with an accompanying video on Youtube? Use only the Mid channel for clean mono without any phasing issues. The real strength of mid-side is the flexibility and versatility it offers after the fact.

The one catch with mid-side, as with all stereo techniques, is that it requires two distinct microphones. ORTF requires two cardioid mics and a bar to mount them on. A/B requires two widely spaced omnis. Even my SASS consists of two omni mics mounted in an admittedly rather large baffle. M/S is no different, requiring a cardioid and a figure-eight.

What makes M/S special is that you want the microphones to be as close to each other as you can get them. By its very design it’s inherently physically compact. (Side note: This is true of X/Y as well, which uses two cardioids pointing 90 degrees to each other, and of the Blumlein arrangement, which replaces the cardioids with figure-eights.)

Which leads us back to Jules’s M/S microphone, which takes “compact” to a new level by cramming multiple microphones into just one mic body. That makes for a light, portable recording kit that’s quick to set up and tear down; perfect for traveling, or for recording subjects that require substantial hiking to reach.

So why three capsules instead of two? Jules realized that if he took two of the TSB-165 cardioid capsules, faced them in opposite directions, and wired them 180 degrees out of phase with each other in series, they act like a single microphone with a figure-eight pickup pattern. Add a third TSB-165 capsule in the center and you have all the makings of a well matched mid-side microphone.

Where Things Stand Now

My parabolic reflector arrived last week. The mic for the parabolic project is already in-hand, though I may have to (yet again) cut it out of its housing and install it in a new one. I’m in the process of designing the mechanical bits, and should be able to start making them in the next couple of weeks.

I ordered the BM-800 donor mic for my mid-side mic just this morning. Jules posted a link to download the Pimped Alice PCB files that Homero Leal designed based off of Scott Helmke’s original Alice design. Once I have the board mounting hole pattern off of the BM-800 microphone, I’ll add those to Homero’s PCB layout and send the files off to OSH Park for fab.

Work on both of these is contingent on my getting a number of other gotta-do’s off my plate, but I hope to make some progress on both in the next couple of weeks.


Posted in Audio, Engineering | Tagged: , , , , , , , , , , , , , , , | 1 Comment »

SASS and ORTF Side-by-Side

Posted by Tom Benedict on 09/08/2016

Or top and bottom, rather.

I had the opportunity to stick my SASS rig and my newly minted ORTF bar on the same mount, one right over the other, and use them to record coqui frogs in a eucalyptus forest on the Big Island of Hawaii.

Of course whenever you record in a forest here you also get insects.

And if you happen to be within a hundred yards of a bunch of… dinosaurs? You also get them.

And the rain.

Ok, just a bunch of stuff. Anyway, here’s the recording. It’s an A-B test, switching between SASS and ORTF at thirty second intervals with a two second cross-fade.

My take: The two are different. (Well duh!) They provide different sounds. Neither one is “right” to my ear, just… different. But I’ll let you decide for yourself.


P.S. No I didn’t say which is which in the recording. What would be the fun of that?

Posted in Audio | Tagged: , , , , , , , , | 2 Comments »

Clippy EM184 Cardioid Mics and ORTF

Posted by Tom Benedict on 05/08/2016

I’d planned to write an article describing my trip to Edinburgh for SPIE 2016, but I got side-tracked. That article is yet to come.

I did some audio recording while I was there, but not nearly as much as I’d have liked. I wound up packing all of my sound gear, including my SASS, but the few times I pulled it out it rained. The one time I thought I’d get to use it for sure – poking it out of my hotel room window to record traffic sounds – I found it was too big to fit through the window. I wound up using spaced omnis to record traffic sounds, but the SASS didn’t get used even once. I found myself wishing I had other options.

A number of common stereo techniques require the use of cardioid microphones. Up until my trip to Scotland I only had omni microphones in my bag. There are still some stereo techniques that use omnis that I haven’t tried, but I’ve been wanting to play with cardioid mics for some time. Step one was to buy or make some cardioids.

The same circuit I used to make my EM172 omni mics can be used with other FET-enabled Primo capsules, including the EM184 cardioid capsule. FEL Communications (micboosters) sells these on their site either as individual caps or as matched pairs. I picked up a matched pair along with a pair of Clippy mic bodies, clips, and windscreens. I still had some Mogami cable and Neutrik connectors on hand, so I just drew from that stock to build out the new mics.

The Clippy mic bodies work nicely with the cardioid capsules, and the resulting mics have very little pickup at the back. It’s not zero, though, so you do have to be aware of everything that’s not directly in front of the mic. I’d been warned that cardioids are more sensitive to wind than omnis, and these mics bear that out. They’re stupid sensitive to wind. Even with the foam windscreens and some furries I got from Cat Ears, the slightest bit of wind kills them. I need to figure out some other solution for wind protection.

Step two was to come up with a way to hold the mics so they record a clean, well separated stereo image. There are plenty of choices for this, but the one I chose was ORTF, a technique designed around 1960 by Office de Radiodiffusion Télévision Française (ORTF) at Radio France. (See? Astronomers aren’t the only ones to recycle their acronyms!)

ORTF requires the microphones to be separated by 170mm and angled away from each other at a 110 degree angle. It’s a bit of a pain to set up in the field without some way to gauge the angle, so many people favor other setups such as NOS (Nederlandse Omroep Stichting) in which the mics are separated by 300mm and are angled out by 90 degrees. I wanted to play with ORTF, though, so I decided to solve the setup problems with a fixture.

Clippy ORTF Bar

Since the Clippy mic bodies register nicely with their lapel clips, I used the clips to orient the mics both in location and rotation. The clips have a tab on top that’s just over 6.2mm wide. I made 6.5mm wide slots at either end of a bar to receive the clips.

Clippy ORTF Bar With Mics

I wanted to keep things simple so I didn’t have to fuss with stuff in the field, and this lets me do that. With the clips fully seated in the slots the mics are angled out at a 110 degree angle and are 170mm apart. It takes more time to unroll the cables than it does to install the mics on the fixture. And the flat bar packs down a lot smaller than my SASS.

Clippy ORTF Bar Slot Detail

The bar I used was just over 4mm thick. I cut the slots to leave 2mm of material for the mic to clip to. This wound up being a little thin, but it made for a nice, deep slot to register the clip in.

Clippy ORTF Bar Velcro

The bare metal of the bar was too slick for the clip to get any real grip, so I put a tab of Industrial Velcro on the bottom of the bar under each of the slots so the clips would have something to grab onto.

I’m pleased with how easy it is to use this setup, and it’s tough to beat how compact it is. But I’m not 100% satisfied with how it works in the field just yet. I already mentioned the wind issue. Even with double protection the mics saturate when almost any amount of wind touches them. They’ll probably fare better inside  a Rycote or a Rode blimp, but for now I’ll have to save them for wind-free environments.

The sound is also significantly different from that of my SASS. (Sorry, no side-by-side comparisons yet.) The SASS picks up more reverberation than the ORTF setup, so there’s more of a sense of the space with the SASS than with the ORTF. But you don’t always want that sense of space. During an earlier test I had one of my omnis and one of the cardioids in a car. The omni picked up so much of the car noise, it was difficult to hear the people in the car speaking. The recording from the cardioids was much cleaner.

Needless to say there’s still plenty of testing to be done. Once I learn the strengths and weaknesses of this setup and have a better handle on wind protection, I’m sure it’ll see plenty of use.


Posted in Audio, Engineering | Tagged: , , , , , , , , , , , | 4 Comments »

IDCD 2016 – Part 2

Posted by Tom Benedict on 02/05/2016

Cloud Forest

As it turns out it did rain, but my gear survived!

Unfortunately the sound of the raindrops falling on the koa leaves that lined the forest floor dominated the soundscape during the dawn chorus. Koa leaves are very flat, and provide no loft to the forest floor to absorb the shock of a raindrop hitting. It has all the acoustic properties of water drops hitting wet cardboard. Even more unfortunate, the low-slung arrangement of my SASS meant that the microphones were only about 12″ from the forest floor. I basically close-mic’ed the raindrops, and left the birds in the diffuse soundfield. That’s the opposite of what I wanted!

But I’ll let you judge for yourself. Here’s the dawn chorus from the Upper Waiakea Forest Reserve in its entirety:

(I still haven’t figured out how to make a nice, neat link to Soundcloud files.)

Despite the rain I’m taking it as a win. The gear setup works, I can leave it deployed overnight, and it can survive rain. YAY! But it places the mics too close to the ground for it to ever work well with rain. I’ll have to come up with another arrangement for recording rainfall, preferably something that lets me position the mics a good deal higher up in the air. (More R&D!)

In case you’re wondering what the birds sound like when it’s not raining, this is a sample from the evening before International Dawn Chorus Day, before the birds went to bed and well before the rain started.

Unfortunately, despite being over a mile from the highway some traffic noise is still audible in parts of the full-length track. The next time I do this I need to find a more secluded spot to set my gear.


Posted in Audio | Tagged: , , , , , , | 1 Comment »